Accessories of solar inverter

A specialized tool for safely disconnecting AC trunk ports, ensuring ease of maintenance and system management in SolaX X1 Micro-Inverter installations.

Connector's hood for IQ Enphase micro-inverter. 

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

Male AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

LAN communication card to connect your SOLAX inverter and monitor its performance remotely.

Female AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

Use this connector from TRONC for SOLAX X1 microinverters to connect AC cables and microinverters. You have one side with a male end and the other female end. The 3rd is the end piece for connecting the SOLAX microinverter connector.

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

The connectors are located 1.3m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

Female connector for IQ Enphase micro-inverter. 

Male connector for IQ Enphase micro-inverter. 

Termination cap APS for the last micro-inverter. 

This tip of ending is completely sealed and waterproof. Be careful when you attach this piece to your IQ Enphase cable: you can only remove it by cutting. Make sure you order the right cable length.

Proper installation with our Enphase products. 

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

The connectors are located 2m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS micro-inverters you have ordered.

This solution is ready to use.

Here you can find the suitable cable with a length of 5m for the APS EZ1. It is needed to connect the EZ1 to the mains. You can also connect another socket by disconnecting the type C plug.

Length 1.3 meters
Three-phase

The connectors are located 2m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

A convenient 5-meter Plug-and-Play cable designed specifically for seamless integration with SolaX X1 Micro-Inverters, simplifying installation processes.

The SolaX adapter box is combined with a heat pump with dry contact function.
As long as your appliance has a dry contactor, this box allows your appliance to be connected to the photovoltaic inverter. The inverter controls the box to activate your heater according to your settings (available panel power, battery status, time, etc.).

Typically customers activate when there is excess solar energy and battery storage capacity. This part of the energy can be used to activate the heat pump or cumulus in the required temperature range.

Note: The adapter box is only compatible with SolaX Hybrid G4 and Boost G4 models. 

Length 2.3 meters
Three-phase

Order the AC cable for SOLAX X1 microinverter with a length of 1.6m. Generally used for installations with solar panels in vertical format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

Measure the current in your home with this sensor. It plugs directly into your Chint DDSU or DTSU meter.
Then connect this plug around the cable that runs between your home's electrical panel and your electricity supplier's meter.

These CT clamps can measure currents between 5A and 200A.

The diameter of these clamps is 24mm.

These clamps are programmed to work with SOLAX inverters and CHINT meters.

Add ENPHASE current transformers to monitor a polyphase or three-phase installation with the ENVOY-S Metered.

The SolarEdge 100 A current meter measures the current of your home and in the power grid. Connect to the SolarEdge electricity meter.

Order the AC cable for SOLAX X1 microinverter with a length of 2.2m. Generally used for installations with solar panels in horizontal format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

The connectors are located 2.4m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS QT2 micro-inverters you have ordered.

This solution is ready to use.

For FRONIUS and SMA inverters.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

ECU B only works for the communication of up to 4 solar panels.

Plug & Play connection to inverter
Wifi communication via Smart Dongle-Wifi
Support of 3rd-party monitoring systems

External Relay for IQ7 In Enphase installations, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

Wifi communication card to connect your SOLAR-EDGE inverter via Wifi and monitor its performance remotely.

Measure the current in your home with this sensor that plugs around the chosen power cable. 

Connect up to 3 cables.