Accessories

Protection box for batteries at 30A, 500 V DC.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

4-pin shielded cable Li2YCYv for RS485 cabling, 30 meters (indoor and outdoor)

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Cable 1x4 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

Measure the consumption of your home and the power injected into the power grid. This meter is connected to AURORA VISION. This meter is also connected to your inverter. It allows you to readjust the power of your solar panels so as not to inject the overproduction into the power grid.

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

For SMA inverter STPxxxTL-30 on input A + B

Production meter in kWh and partial meter with reset. Single-phase.
Rated voltage: 230 V/50 Hz
Start Current: 20 mA
Maximum current: 80 A

Crimping tool for connecting MC4 connectors to the solar cable.

Fronius smart meter 100 A single-phase to monitor the consumption of your home and adjust the production of the inverter. This meter communicates with your Fronius inverter and avoids the injection of surplus from your inverter into the power grid.

Heavy Duty True RMS industrial digital multimeter, CAT III 1000V / CAT IV 600V with VFD mode.

Low-pass filter for motor traction measurements.

Backlit LCD display: 6000 measurement points. AC frequency band from 45Hz to 1kHz.

Audiovisual continuity indicator. Automatic sleep mode. Battery status indicator. Data Hold function.

Auto Ranging.

MIN/MAX function.

TRMS measurement.

Relative measurement.

IP67 input protection (waterproof and dustproof).

Control and immediate monitoring of your installations by connecting to your network ! 

With this Base Unit, the new SMA Home Storage can be set up directly on the floor as an alternative to the supplied wall bracket. One base is required for each battery tower.

This electric cable with a section of 4mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

This electric cable with a section of 2.5 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

The ECC gateway connects your microinverters to the Solax cloud application, enabling you to retrieve and manage all the information from your microinverters.

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

Mounting bracket for fixing your Ecoflow PowerOcean battery to the ground.

Connection for SMA and FRONIUS up to 150A. Length 0.5m.

This electric cable with a section of 6 mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Plug & Play connection to inverter
4G communication via Smart Dongle-4G
Support max 10 inverters communication

High Compatibility
Compatible with both single-phase and three-phase meters

Easy Installation
Supports din-rail installation inside the cabinet for 85 Vac-277 Vac power supply

Wide Coverage
Offers efficient and stable data transmission of up to 300 m long distance

Strong Penetration
With better signal through the wall effect, can provide up and down multi-floor communication, strong anti-interference ability

Cable 1x6 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

For SMA inverter Core1 set complet

Wall mount for GoodWe Lynx batteries. You only need one piece per location. Up to 4 GoodWe batteries.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 250 A.

Order your tools at the best price to mount your solar panels on your customers' roofs. This system can go up to 10m high. Supplied with a forklift trolley or support for placing the solar panels, you'll have the flexibility you need for your installation.

The system's variable-speed electric motor ensures that your panels go up smoothly. The system is highly flexible and adapts perfectly to different roofs.

The Enphase COMMS kit is required to establish the data connection between the IQ-5P Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

The Enphase COMMS kit is required to establish the data connection between the Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

This meter measures the power injected into the electrical network, the consumption of your home. It measures a voltage of 220V to 240V. To be used for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps 120A/40mA.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 220V to 240V. Use it for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A/phase.

50 meter ground cable 8UL1015 green/yellow 6 mm²

Accessories for TRIPLE POWER batteries including:
- Cover to put the H9-H12 batteries in 2 columns
- Cables between the 2 columns
- Screws