Accessories

This electric cable with a section of 2.5mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Protection box for batteries at 30A, 500 V DC.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

4-pin shielded cable Li2YCYv for RS485 cabling, 30 meters (indoor and outdoor)

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Cable 1x4 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

Measure the consumption of your home and the power injected into the power grid. This meter is connected to AURORA VISION. This meter is also connected to your inverter. It allows you to readjust the power of your solar panels so as not to inject the overproduction into the power grid.

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

For SMA inverter STPxxxTL-30 on input A + B

Production meter in kWh and partial meter with reset. Single-phase.
Rated voltage: 230 V/50 Hz
Start Current: 20 mA
Maximum current: 80 A

Crimping tool for connecting MC4 connectors to the solar cable.

Heavy Duty True RMS industrial digital multimeter, CAT III 1000V / CAT IV 600V with VFD mode.

Low-pass filter for motor traction measurements.

Backlit LCD display: 6000 measurement points. AC frequency band from 45Hz to 1kHz.

Audiovisual continuity indicator. Automatic sleep mode. Battery status indicator. Data Hold function.

Auto Ranging.

MIN/MAX function.

TRMS measurement.

Relative measurement.

IP67 input protection (waterproof and dustproof).

Control and immediate monitoring of your installations by connecting to your network ! 

With this Base Unit, the new SMA Home Storage can be set up directly on the floor as an alternative to the supplied wall bracket. One base is required for each battery tower.

This electric cable with a section of 4mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

This electric cable with a section of 2.5 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

Battery protection box up to 125A for batteries operating at 48V DC.

The ECC gateway connects your microinverters to the Solax cloud application, enabling you to retrieve and manage all the information from your microinverters.

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

Mounting bracket for fixing your Ecoflow PowerOcean battery to the ground.

Connection for SMA and FRONIUS up to 150A. Length 0.5m.

This electric cable with a section of 6 mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Plug & Play connection to inverter
4G communication via Smart Dongle-4G
Support max 10 inverters communication