Accessories

This single-phase Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid SK-SU and Solax Hybrid X1-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

Extend your ABB inverter warranty TRIO-5.8-TL to 10 years.

The WALLBOX power boost measures the power taken from the network, sends the data to the WALLBOX charger so that it regulates the charging power and avoids excessive energy consumption in the home, eliminating any risk of blackout.

If you have a FRONUIS GALVO SYMO or PRIMO Light version, you can add this card to establish a WIFI connexion.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

In addition to controlling the surplus management, you can remotely activate your hot water tank.

BMS module for Growatt battery that works only with Growatt MIN single phase hybrid inverters. Comes with stand for floor installation.

The Zaptec Sense is designed to make smart use of energy in homes. This system measure the power need and adapt automatically the charging speed to avoid any defaults. Your vehicle can be charged faster when little power is used. The Zaptec Sense avoids overload and power outages when it uses a lot of power.

Measures up to 63A on 3 phases. Also works on single-phase installations (limited to 21A in this case).

Measure the current of your home with this sensor that plugs around the corresponding power cable.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 100V to 380V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

This meter measures the power injected into electrical grid, consumption of your home and power from another inverter SOLAX brand or other(dual version). The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 40V to 400V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

Fronius three-phase smart meter 65A-3 monitors the consumption of your home and adjusts the inverter's production. This meter communicates with your Fronius inverter and avoids the injection of surplus from your inverter into the power grid.

Through-current meter, no CT clamp required.

Tool to connect the MULTI-CONTACT solar cable connectors.

3-phase measurement solution with SMA wire-speed interface for phase-accurate and netted determination of electrical values (limiting current 63A)

Connects directly to the KOSTAL inverter to monitor your home consumption and regulate the solar panels' power.

The next-generation Envoy-S Metered provides energy usage insights, remote update capabilities and load management, enabling a more cost-effective and reliable solar installation while adding significant value for system owners. "Metered" version.

Including 2 portals with Envoy-S Metered.

Extend your FRONIUS inverter warranty Fronius GEN24 SYMO to 10 years.

This Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid X3-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

The SOLAX Series Box is used to install several towers. It is required for more than a total of 10 batteries to connect the products in series.
Compatible with Solax Triple Power HV-S2.5 and HV-S3.6 batteries.

With the SolaX Series Box, you can add a second battery tower to the X3 IES battery system connected to the inverter.

The Series Box also contains a base for the second battery tower and other necessary accessories such as power and communication cables.

The article is mandatory if you want to use more than 4 batteries in your IES system.

The BYD Combiner Box centralizes high-voltage battery connections to simplify and secure installations. Compatible with BYD storage systems, it optimizes energy management thanks to built-in protection and easy configuration.

Connect 2 or 3 battery stacks.

This base is essential if you wish to install the new ENPHASE 5P batteries on the floor.

The IQ Energy Router integrates Enphase solar and battery storage systems with electric vehicle charging stations to optimize self-consumption and minimize costs.

BMS module for Growatt battery that works only with Growatt MOD single phase hybrid inverters. Comes with stand for floor installation.