Accessories of solar inverter

A specialized tool for safely disconnecting AC trunk ports, ensuring ease of maintenance and system management in SolaX X1 Micro-Inverter installations.

Connector's hood for IQ Enphase micro-inverter. 

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

Male AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

LAN communication card to connect your SOLAX inverter and monitor its performance remotely.

Female AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

Use this connector from TRONC for SOLAX X1 microinverters to connect AC cables and microinverters. You have one side with a male end and the other female end. The 3rd is the end piece for connecting the SOLAX microinverter connector.

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

The connectors are located 1.3m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

Female connector for IQ Enphase micro-inverter. 

Male connector for IQ Enphase micro-inverter. 

Termination cap APS for the last micro-inverter. 

This tip of ending is completely sealed and waterproof. Be careful when you attach this piece to your IQ Enphase cable: you can only remove it by cutting. Make sure you order the right cable length.

Proper installation with our Enphase products. 

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

The connectors are located 2m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS micro-inverters you have ordered.

This solution is ready to use.

Here you can find the suitable cable with a length of 5m for the APS EZ1. It is needed to connect the EZ1 to the mains. You can also connect another socket by disconnecting the type C plug.

Length 1.3 meters
Three-phase

The connectors are located 2m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

A convenient 5-meter Plug-and-Play cable designed specifically for seamless integration with SolaX X1 Micro-Inverters, simplifying installation processes.

The SolaX adapter box is combined with a heat pump with dry contact function.
As long as your appliance has a dry contactor, this box allows your appliance to be connected to the photovoltaic inverter. The inverter controls the box to activate your heater according to your settings (available panel power, battery status, time, etc.).

Typically customers activate when there is excess solar energy and battery storage capacity. This part of the energy can be used to activate the heat pump or cumulus in the required temperature range.

Note: The adapter box is only compatible with SolaX Hybrid G4 and Boost G4 models. 

Length 2.3 meters
Three-phase

Order the AC cable for SOLAX X1 microinverter with a length of 1.6m. Generally used for installations with solar panels in vertical format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

Measure the current in your home with this sensor. It plugs directly into your Chint DDSU or DTSU meter.
Then connect this plug around the cable that runs between your home's electrical panel and your electricity supplier's meter.

These CT clamps can measure currents between 5A and 200A.

The diameter of these clamps is 24mm.

These clamps are programmed to work with SOLAX inverters and CHINT meters.

Add ENPHASE current transformers to monitor a polyphase or three-phase installation with the ENVOY-S Metered.

The SolarEdge 100 A current meter measures the current of your home and in the power grid. Connect to the SolarEdge electricity meter.

Order the AC cable for SOLAX X1 microinverter with a length of 2.2m. Generally used for installations with solar panels in horizontal format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

The connectors are located 2.4m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS QT2 micro-inverters you have ordered.

This solution is ready to use.

For FRONIUS and SMA inverters.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

ECU B only works for the communication of up to 4 solar panels.

Plug & Play connection to inverter
Wifi communication via Smart Dongle-Wifi
Support of 3rd-party monitoring systems

External Relay for IQ7 In Enphase installations, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

Wifi communication card to connect your SOLAR-EDGE inverter via Wifi and monitor its performance remotely.

Measure the current in your home with this sensor that plugs around the chosen power cable. 

Connect up to 3 cables.

For SMA inverter Core1 set complet

Zigbee range extender dongle operating in 2.4GHz band for the Enphase IQ Battery To be used in specific conditions (not mandatory) specified in installation manual

Temperature sensor for SUNNY ISLAND. This sensor permit you to use a Lead battery.

Connects your SolarEdge inverter wirelessly to the Internet.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

This kit connect MKS inverters in parallel and also three-phase working. Only for 5kVA.

The SolarEdge switch with meter diverts photovoltaic power to an electrical appliance (load) according to a pre-configured time schedule.

For SMA inverter STPxxxTL-30 on input A + B

The SolarEdge Smart Energy management solutions allow you to switch to self-consumption at home. This plug allows you to monitor the consumption in your home. Power management for up to 2.5 kW.

The ECC gateway connects your microinverters to the Solax cloud application, enabling you to retrieve and manage all the information from your microinverters.

Plug & Play connection to inverter
4G communication via Smart Dongle-4G
Support max 10 inverters communication

High Compatibility
Compatible with both single-phase and three-phase meters

Easy Installation
Supports din-rail installation inside the cabinet for 85 Vac-277 Vac power supply

Wide Coverage
Offers efficient and stable data transmission of up to 300 m long distance

Strong Penetration
With better signal through the wall effect, can provide up and down multi-floor communication, strong anti-interference ability

For SMA inverter Core1 set complet

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 250 A.

The Enphase COMMS kit is required to establish the data connection between the IQ-5P Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

The Enphase COMMS kit is required to establish the data connection between the Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

This meter measures the power injected into the electrical network, the consumption of your home. It measures a voltage of 220V to 240V. To be used for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps 120A/40mA.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 220V to 240V. Use it for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

External Relay for IQ7 In Enphase installations three-phase, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

The Enphase Envoy communications gateway is the core of your network. Homeowners can easily monitor the status of their system using the LCD screen of the Envoy and get more detailed information for each module via Enlighten, the monitoring and analysis software by Enphase.

WIFI directly included in this ENVOY-S gateway.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

The Modbus SolarEdge meter is used for photovoltaic supervision, consumption monitoring at home and for monitoring the power grid. The meter measures currents from 50 A to 1,000 A and supports residential and commercial installations. The meter connects to the SolarEdge inverter or gateway control and communication via RS485.

Card for Kostal product extension. Specific card for Germany.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

This meter measures the power injected into the electrical network, the consumption of your home. To be used for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with 3 CT clamps 120A/40mA.

Set of 2 reusable handles for easy handling of the IQ-5P battery.

This single-phase Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid SK-SU and Solax Hybrid X1-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

In addition to controlling the surplus management, you can remotely activate your hot water tank.

Connects directly via RS485 to the LG inverter. You will be able to monitor your home consumption and regulate the power of your solar panels. Measures up to 60A in three-phase.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 100V to 380V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

This meter measures the power injected into electrical grid, consumption of your home and power from another inverter SOLAX brand or other(dual version). The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 40V to 400V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

This Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid X3-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

Connects directly to the KOSTAL inverter to monitor your home consumption and regulate the solar panels' power.

3-phase measurement solution with SMA wire-speed interface for phase-accurate and netted determination of electrical values (limiting current 63A)

The next-generation Envoy-S Metered provides energy usage insights, remote update capabilities and load management, enabling a more cost-effective and reliable solar installation while adding significant value for system owners. "Metered" version.

Including 2 portals with Envoy-S Metered.

The IQ Energy Router integrates Enphase solar and battery storage systems with electric vehicle charging stations to optimize self-consumption and minimize costs.

Heater controller which adjusts the power supplied to the heater based on the available power currently produced by your photovoltaic panels (up to 3 kW).

Heater controller which adjusts the power supplied to the heater based on the available power currently produced by your photovoltaic panels (up to 5 kW).

For SOLAX inverters G4 versions, you can eliminate complex cable connections by using the MATEBOX. This box includes:

- EPS BOX
- Circuit breaker
- CT Clamp

SMA inverter production recorder (up to 50 units). The SUNNY HOME MANAGER communicates with the inverters via SPEEPDWIRE/Bluetooth link. It transfers all the data for analysis and display to an Internet server or to a local PC (integrated web server). The new version 2.0 of the SUNNY HOME MANAGER allows you to manage your electrical appliances remotely via connected electrical outlets, enable/disable them remotely and analyze your energy balance.

The new Sunny Home Manager 2.0 combines the functions of the Sunny Home Manager Bluetooth and the SMA Energy Meter in one single device.

The SMA Portal will advise you in energy saving via a simple and ergonomic interface. SMA offers this service free of charge.

Ideal solution to manage string inverters by SMA (type SunnyBoy or Sunny Tripower). Allows to manage the power output, to integrate sensors (temperature, sunlight, etc.). Equipped with a web server: It can send the data of up to 50 SMA inverters to the online server.

For SOLAX inverters G4 versions, you can eliminate complex cable connections by using the MATEBOX. This box includes:

• EPS BOX
• Circuit breaker
• Disconnector
• Meter

This Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid X3-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

This Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid X3-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.