Accessories

Quick and easy installation without any tools. For 4
and 6mm2 cable. No risk:
- Cable breakage
- Induction loop
- Rodents
- Premature ageing of the cable

A specialized tool for safely disconnecting AC trunk ports, ensuring ease of maintenance and system management in SolaX X1 Micro-Inverter installations.

Connector's hood for IQ Enphase micro-inverter. 

To ground your solar panels at home.

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

10x connectors for ⌀6mm ground cable, M8 hole to ground your photovoltaic system.

Male AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

LAN communication card to connect your SOLAX inverter and monitor its performance remotely.

Adapter, patch cable, RJ45. CAT5E
RJ45 M, 2 X RJ45 F, length 0.19 M

1 x RJ45 male to 2 x RJ45 female, 8-pole, 1:1 wiring.

Female AC plugs designed for secure and efficient connection within SolaX X1 Micro-Inverter systems, ensuring reliable power transmission.

SMA battery communication cable 3 metersSMA connection cable for SMA Home Storage batteries.
3 meters long
Suitable for outdoor installation.

Tool to connect the MULTI-CONTACT solar cable connectors.

Use this connector from TRONC for SOLAX X1 microinverters to connect AC cables and microinverters. You have one side with a male end and the other female end. The 3rd is the end piece for connecting the SOLAX microinverter connector.

Multi-contact MC4 connectors for connecting solar panels. Connect one string with 1 cable.

Multi-contact MC4 connectors for connecting solar panels

This tool allows you to disconnect your IQ Enphase micro-inverter from its connector. It can also be used to tighten the tip termination.

This product is very useful for mounting all Enphase products. 

The connectors are located 1.3m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

4-pin shielded cable Li2YCYv for RS485 cabling, 10 meters (indoor and outdoor)

Female connector for IQ Enphase micro-inverter. 

Male connector for IQ Enphase micro-inverter. 

Cable duct with a length of 2m, white color with a dimension of 60x40mm. This duct allows you to pass up to 16 cables. Be careful, you must not mix solar cables (DC direct current) and alternating cables (AC alternating current) in the same duct.

MC4 multi-contact brand connectors for connection to solar panels and for SOLAX battery. This MC4 variant has a sealing ring.

Connectors MC4 for connecting solar panels

This MC4 variant has a sealing ring.

Termination cap APS for the last micro-inverter. 

This tip of ending is completely sealed and waterproof. Be careful when you attach this piece to your IQ Enphase cable: you can only remove it by cutting. Make sure you order the right cable length.

Proper installation with our Enphase products. 

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

The connectors are located 2m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS micro-inverters you have ordered.

This solution is ready to use.

10x multi-contact connectors MC4 for connecting solar panels

The wood construction screws plate head have a 10-fold higher corrosion protection due to their Wirox surface.

In addition, a corrugated profile right up to the tip ensures quick and easy screwing in. The screws can be screwed in without pre-drilling. Screws pan head saves up to 30% time and money compared to alternative pan head screws. The pan head guarantees high head pull-through values, thus enabling larger screw spacing. The T-Star Plus drive ensures a clean fit of the bit. The screws are marked on the head with the length and manufacturer's identification. Free static calculation software is also available.

10x multi-contact connectors MC4 for connecting solar panels.

Measure the electricity in your home with this sensor, which is connected between your home's electricity box and your electricity supplier's meter.
This product is suitable for the Solax X1 Mini and Boost series.

Here you can find the suitable cable with a length of 5m for the APS EZ1. It is needed to connect the EZ1 to the mains. You can also connect another socket by disconnecting the type C plug.

Length 1.3 meters
Three-phase

The connectors are located 2m apart from eachother in portrait mode. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of Enphase micro-inverters you have ordered.

This solution is ready to use.

Holds up to 70 kg

Battery cable for TRIPLE POWER H12.0 battery with a length of 1.2m

A convenient 5-meter Plug-and-Play cable designed specifically for seamless integration with SolaX X1 Micro-Inverters, simplifying installation processes.

The SolaX adapter box is combined with a heat pump with dry contact function.
As long as your appliance has a dry contactor, this box allows your appliance to be connected to the photovoltaic inverter. The inverter controls the box to activate your heater according to your settings (available panel power, battery status, time, etc.).

Typically customers activate when there is excess solar energy and battery storage capacity. This part of the energy can be used to activate the heat pump or cumulus in the required temperature range.

Note: The adapter box is only compatible with SolaX Hybrid G4 and Boost G4 models. 

Length 2.3 meters
Three-phase

Order the AC cable for SOLAX X1 microinverter with a length of 1.6m. Generally used for installations with solar panels in vertical format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

Measure the current in your home with this sensor. It plugs directly into your Chint DDSU or DTSU meter.
Then connect this plug around the cable that runs between your home's electrical panel and your electricity supplier's meter.

These CT clamps can measure currents between 5A and 200A.

The diameter of these clamps is 24mm.

These clamps are programmed to work with SOLAX inverters and CHINT meters.

Add ENPHASE current transformers to monitor a polyphase or three-phase installation with the ENVOY-S Metered.

The SolarEdge 100 A current meter measures the current of your home and in the power grid. Connect to the SolarEdge electricity meter.

Order the AC cable for SOLAX X1 microinverter with a length of 2.2m. Generally used for installations with solar panels in horizontal format. It connects to the SOLAX trunk connector and allows the connection of all microinverters.

Battery cable for TRIPLE POWER H9.0 battery with a length of 1.8m

KNIPEX - Pince à sertir pour fiches Western RJ11 / RJ12 / RJ45, longueur 190mm

Electrical conduit for outdoor installation. You can run up to 8 wires inside. Be careful not to mix solar cables (direct current) and alternating current cables. Supplied with the wire puller to facilitate the installation of your cables indoors.

The connectors are located 2.4m apart from eachother. The quantity you select refers to the number of connectors. The connectors are already mounted on the cable. Of course this number is linked to the number of APS QT2 micro-inverters you have ordered.

This solution is ready to use.

For FRONIUS and SMA inverters.

Cable 1x4 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

ECU B only works for the communication of up to 4 solar panels.

With this card, the ABB inverter will automatically adapt the output power in order to maximise self-consumption or in order to avoid feeding power into the grid according to the system settings.

In addition, this UNO-DM-COM KIT is equipped with a configurable switching relay which can be used for manage external loads with custumizable activation power and temporal thresholds (basic load management capability).

The ABB inverter can be easily integrated with third party monitoring and control systems using this accessory board.

Plug & Play connection to inverter
Wifi communication via Smart Dongle-Wifi
Support of 3rd-party monitoring systems

External Relay for IQ7 In Enphase installations, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

Wifi communication card to connect your SOLAR-EDGE inverter via Wifi and monitor its performance remotely.

Measure the current in your home with this sensor that plugs around the chosen power cable. 

Connect up to 3 cables.

For SMA inverter Core1 set complet

Fixing for floor installation of GoodWe Lynx batteries. You only need one piece per location.

Cable 1x4 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

Zigbee range extender dongle operating in 2.4GHz band for the Enphase IQ Battery To be used in specific conditions (not mandatory) specified in installation manual

Temperature sensor for SUNNY ISLAND. This sensor permit you to use a Lead battery.

This electric cable with a section of 2.5mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Connects your SolarEdge inverter wirelessly to the Internet.

Protection box for batteries at 30A, 500 V DC.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

4-pin shielded cable Li2YCYv for RS485 cabling, 30 meters (indoor and outdoor)

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A.

This kit connect MKS inverters in parallel and also three-phase working. Only for 5kVA.

Cable 1x4 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

The SolarEdge switch with meter diverts photovoltaic power to an electrical appliance (load) according to a pre-configured time schedule.

Measure the consumption of your home and the power injected into the power grid. This meter is connected to AURORA VISION. This meter is also connected to your inverter. It allows you to readjust the power of your solar panels so as not to inject the overproduction into the power grid.

For SMA inverter STPxxxTL-30 on input A + B

Production meter in kWh and partial meter with reset. Single-phase.
Rated voltage: 230 V/50 Hz
Start Current: 20 mA
Maximum current: 80 A

Crimping tool for connecting MC4 connectors to the solar cable.

Heavy Duty True RMS industrial digital multimeter, CAT III 1000V / CAT IV 600V with VFD mode.

Low-pass filter for motor traction measurements.

Backlit LCD display: 6000 measurement points. AC frequency band from 45Hz to 1kHz.

Audiovisual continuity indicator. Automatic sleep mode. Battery status indicator. Data Hold function.

Auto Ranging.

MIN/MAX function.

TRMS measurement.

Relative measurement.

IP67 input protection (waterproof and dustproof).

Control and immediate monitoring of your installations by connecting to your network ! 

Fronius smart meter 100 A single-phase to monitor the consumption of your home and adjust the production of the inverter. This meter communicates with your Fronius inverter and avoids the injection of surplus from your inverter into the power grid.

The SolarEdge Smart Energy management solutions allow you to switch to self-consumption at home. This plug allows you to monitor the consumption in your home. Power management for up to 2.5 kW.

This electric cable with a section of 4mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

This electric cable with a section of 2.5 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

The ECC gateway connects your microinverters to the Solax cloud application, enabling you to retrieve and manage all the information from your microinverters.

Connection for SMA and FRONIUS up to 150A. Length 0.5m.

This electric cable with a section of 6 mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Plug & Play connection to inverter
4G communication via Smart Dongle-4G
Support max 10 inverters communication

High Compatibility
Compatible with both single-phase and three-phase meters

Easy Installation
Supports din-rail installation inside the cabinet for 85 Vac-277 Vac power supply

Wide Coverage
Offers efficient and stable data transmission of up to 300 m long distance

Strong Penetration
With better signal through the wall effect, can provide up and down multi-floor communication, strong anti-interference ability

Cable 1x6 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

For SMA inverter Core1 set complet

Wall mount for GoodWe Lynx batteries. You only need one piece per location. Up to 4 GoodWe batteries.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 250 A.

Order your tools at the best price to mount your solar panels on your customers' roofs. This system can go up to 10m high. Supplied with a forklift trolley or support for placing the solar panels, you'll have the flexibility you need for your installation.

The system's variable-speed electric motor ensures that your panels go up smoothly. The system is highly flexible and adapts perfectly to different roofs.

The Enphase COMMS kit is required to establish the data connection between the IQ-5P Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

The Enphase COMMS kit is required to establish the data connection between the Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

This meter measures the power injected into the electrical network, the consumption of your home. It measures a voltage of 220V to 240V. To be used for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps 120A/40mA.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 220V to 240V. Use it for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A/phase.

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

50 meter ground cable 8UL1015 green/yellow 6 mm²

External Relay for IQ7 In Enphase installations three-phase, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

Accessories for TRIPLE POWER batteries including:
- Cover to put the H9-H12 batteries in 2 columns
- Cables between the 2 columns
- Screws

Connects in parallel to your electrical circuit and connects directly to your Solax solar inverter to monitor your home consumption and regulate the power of your solar panels.

Measures between 5A and 200A per phase for 24mm diameter cables. 

This electric cable with a section of 4 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

Wifi communication card for connecting your ABB inverters UNO and TRIO via Wifi and monitoring their performance remotely.

Extend your FRONIUS inverter warranty Fronius Galvo 1.5-1, 2.0-1, 2.5-1, 3.0-1, 3.1-1; Fronius Primo 3.0-1; Fronius Symo 3.0-3-S, 3.0-3-M; Fronius Symo Hybrid 3.0-3-S to 10 years.

The Enphase Envoy communications gateway is the core of your network. Homeowners can easily monitor the status of their system using the LCD screen of the Envoy and get more detailed information for each module via Enlighten, the monitoring and analysis software by Enphase.

WIFI directly included in this ENVOY-S gateway.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

The Modbus SolarEdge meter is used for photovoltaic supervision, consumption monitoring at home and for monitoring the power grid. The meter measures currents from 50 A to 1,000 A and supports residential and commercial installations. The meter connects to the SolarEdge inverter or gateway control and communication via RS485.

Card for Kostal product extension. Specific card for Germany.

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

This meter measures the power injected into the electrical network, the consumption of your home. To be used for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with 3 CT clamps 120A/40mA.

With this Base Unit, the new SMA Home Storage can be set up directly on the floor as an alternative to the supplied wall bracket. One base is required for each battery tower.

This electric cable with a section of 6 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

Set of 2 reusable handles for easy handling of the IQ-5P battery.

This single-phase Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid SK-SU and Solax Hybrid X1-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

Extend your ABB inverter warranty TRIO-5.8-TL to 10 years.

The WALLBOX power boost measures the power taken from the network, sends the data to the WALLBOX charger so that it regulates the charging power and avoids excessive energy consumption in the home, eliminating any risk of blackout.

If you have a FRONUIS GALVO SYMO or PRIMO Light version, you can add this card to establish a WIFI connexion.

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

In addition to controlling the surplus management, you can remotely activate your hot water tank.

Connects directly via RS485 to the LG inverter. You will be able to monitor your home consumption and regulate the power of your solar panels. Measures up to 60A in three-phase.

Measure the current of your home with this sensor that plugs around the corresponding power cable.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page.