Home

The SolarEdge switch with meter diverts photovoltaic power to an electrical appliance (load) according to a pre-configured time schedule.

Bifacial gass-glass solar panel
High efficiency
0-5W positive tolerance
30-year guarantee
Total protection

Measure the consumption of your home and the power injected into the power grid. This meter is connected to AURORA VISION. This meter is also connected to your inverter. It allows you to readjust the power of your solar panels so as not to inject the overproduction into the power grid.

For SMA inverter STPxxxTL-30 on input A + B

Production meter in kWh and partial meter with reset. Single-phase.
Rated voltage: 230 V/50 Hz
Start Current: 20 mA
Maximum current: 80 A

Crimping tool for connecting MC4 connectors to the solar cable.

Bifacial gass-glass solar panel
High efficiency
0-5W positive tolerance
30-year guarantee
Total protection

Heavy Duty True RMS industrial digital multimeter, CAT III 1000V / CAT IV 600V with VFD mode.

Low-pass filter for motor traction measurements.

Backlit LCD display: 6000 measurement points. AC frequency band from 45Hz to 1kHz.

Audiovisual continuity indicator. Automatic sleep mode. Battery status indicator. Data Hold function.

Auto Ranging.

MIN/MAX function.

TRMS measurement.

Relative measurement.

IP67 input protection (waterproof and dustproof).

Control and immediate monitoring of your installations by connecting to your network ! 

- Model: FV19

- Dimensions: 1350x250x160 mm

- Material: Plastic

Fronius smart meter 100 A single-phase to monitor the consumption of your home and adjust the production of the inverter. This meter communicates with your Fronius inverter and avoids the injection of surplus from your inverter into the power grid.

Output raised to 97,1%
Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

The SolarEdge Smart Energy management solutions allow you to switch to self-consumption at home. This plug allows you to monitor the consumption in your home. Power management for up to 2.5 kW.

Bifacial gass-glass solar panel
High efficiency
0-5W positive tolerance
30-year guarantee
Total protection

This electric cable with a section of 4mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Output raised to 97,1%
Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

This electric cable with a section of 2.5 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

• Control your consumables remotely via the ALMA SOLAR application
• Measurement of consumption and graphic reading on the application
• Monitoring of socket consumption up to 16A/input
• Scenario activation based on the states of connected devices, solar production, solar battery status, weather, time, location, brightness* (*depends on a device with sensor)

Electrical box (alternative current) for photovoltaic protection. Cabinet including wiring diagram. Required for each photovoltaic system.

AC box 230 V AC single-phase up to 4 kW with differential circuit breaker 16 A - 30 mA + surge arrester type A.

Electrical box for photovoltaic protection. DC box includes wiring diagram. Required for every photovoltaic system.

DC box under 600 V DC, 1 string, switch 25 A, lightning, MC4 

- Model name: S751/3DR-E40
- Number of poles: 3
- Protection current: 63A 25kA
- Voltage rating: 230V / 400V
- Device type: Selective main circuit breaker

- Model name: S751/3DR-E40
- Number of poles: 3
- Protection current: 50A 25kA
- Voltage rating: 230V / 400V
- Device type: Selective main circuit breaker

- Model name: S751/3-E40
- Number of poles: 3
- Protection current: 40A 25kA
- Rated voltage: 230V / 400V
- Device type : Selective main circuit breaker

The ECC gateway connects your microinverters to the Solax cloud application, enabling you to retrieve and manage all the information from your microinverters.

- Model: FD19D ComfortLine

- Protection class: IP2XC

- Current: 63 A

- Dimensions: 1350 x 250 x 160 mm

- Model name: S751/3DR-E40
- Number of poles: 3
- Protection current: 40A 25kA
- Voltage rating: 230V / 400V
- Device type: Selective main circuit breaker

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Connection for SMA and FRONIUS up to 150A. Length 0.5m.

This electric cable with a section of 6 mm2 for single-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

Cable is VDE and IEC certified.

Plug & Play connection to inverter
4G communication via Smart Dongle-4G
Support max 10 inverters communication

- Model name: S751/3DR-E40
- Number of poles: 3
- Protection current: 35A 25kA
- Voltage rating: 230V / 400V
- Device type: Selective main circuit breaker

Microinverter
Single phase
Best perfomance
20 years warranty
Online connection
Integrated consumables management

Supplied with connectors to complete the installation.

Use this meter to measure your home's energy consumption and control it with the ALMA SOLAR app.
Determine the consumption of each appliance in your home.
Comes with 3 clamps: each can be used for one measurement (Clamp 1: Solar + Clamp 2: Battery + Clamp 3: Network).
Works with single-phase or three-phase power.

This meter is required if your solar inverter is not yet compatible with the ALMA SOLAR app.

High Compatibility
Compatible with both single-phase and three-phase meters

Easy Installation
Supports din-rail installation inside the cabinet for 85 Vac-277 Vac power supply

Wide Coverage
Offers efficient and stable data transmission of up to 300 m long distance

Strong Penetration
With better signal through the wall effect, can provide up and down multi-floor communication, strong anti-interference ability

Cable 1x6 mm² photovoltaic CR 100 m

Operation from -50 ° C to 150 ° C / Maximum voltage: 1,000 V

For SMA inverter Core1 set complet

Electrical box for photovoltaic protection. Cabinet including wiring diagram. Required for each photovoltaic system.

DC box under 1,000 V DC, 1 string, switch 25 A, lightning, MC4

Wall mount for GoodWe Lynx batteries. You only need one piece per location. Up to 4 GoodWe batteries.

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 250 A.

Order your tools at the best price to mount your solar panels on your customers' roofs. This system can go up to 10m high. Supplied with a forklift trolley or support for placing the solar panels, you'll have the flexibility you need for your installation.

The system's variable-speed electric motor ensures that your panels go up smoothly. The system is highly flexible and adapts perfectly to different roofs.

The Enphase COMMS kit is required to establish the data connection between the IQ-5P Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

The Enphase COMMS kit is required to establish the data connection between the Encharge storage units and the Enphase Envoy. The data connection runs via Zigbee. It is connected to the Envoy via USB.

This meter measures the power injected into the electrical network, the consumption of your home. It measures a voltage of 220V to 240V. To be used for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps 120A/40mA.

- Model name: S751/3-E40
- Number of poles: 3
- Protection current: 35A 25kA
- Rated voltage: 230V / 400V
- Device type: Selective main circuit breaker

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 220V to 240V. Use it for single-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

To operate several microinverters together, you must add:

1. Main AC connector Ref: X1-AC-Micro-AC-Tcon (as many connectors as microinverters).

2. RefX1-MICRO-AC-TC24M or X1-MICRO-AC-TC22M or X1-MICRO-AC-TC16M

In order to operate a single microinverter, you must add:

1. Main AC connector Ref: X1-AC-Micro-AC-Tcon

2. Ref: X1-MICRO-AC-CONF

We can provide a full quotation on request by email.

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Microinverter
Single phase
Best perfomance
25 years warranty
Online connection

Connects directly to the solar inverter to monitor your home consumption and regulate the solar panels' power. Measures up to 100 A/phase.

Improved performance and increased power
P7 patented technology
Positive tolerance: 10%
Superior strength

Our meters offer various advantages:
- Pulse output programmable S0
- Double rates
- Partial indexes registration resettable
- Energy measurement active/reactive, imported/exported
- Cumulative Index by price
- Can be used in single-phase

Microinverter
Single phase
Best perfomance
25 years warranty
Online connection

50 meter ground cable 8UL1015 green/yellow 6 mm²

Certification in progress, installation not possible at the moment

Microinverter
Single phase
Best perfomance
25 years warranty
Online connection

- Type U51 Sub-distribution Board

 - 400V AC 50/60 Hz

- 834 x 310 x 120 mm

External Relay for IQ7 In Enphase installations three-phase, the Q Relay (Network System Relay Controller) acts as a physical disconnect relay controller for installations.

Improved performance and increased power
P7 patented technology
Positive tolerance: 10%
Superior strength

SOLD IN LOTS OF 36 PANELS - Full pallet

Electrical box (alternative current) for photovoltaic protection. Cabinet includes the wiring diagram. Required for each photovoltaic system.

AC box 230 V AC single-phase up to 6 kW with differential circuit breaker 32 A - 30 mA + surge arrester type A.

Buy your micro-inverter APS DS3-L directly on our online webshop. The micro-inverter APS specification is allows a connexion for 2 solar panels on the same micro-inverter. It optimizes solar panels production and become them completely independent from each orders. With this new technology, you reduce the number of micro-inverter and moreover you optimize profitability: More performance and less expensive.

You must order the APS cable to connect the micro-inverters to each other.

Certification in progress, installation not possible at the moment

Microinverter
Single phase
Best perfomance
25 years warranty
Online connection

- CA14V small distribution cabinet

- Indoor use, Protection II, IP44

- 400V AC 50/60 Hz, 125 A

- Dimensions: 650x300x160 mm

Accessories for TRIPLE POWER batteries including:
- Cover to put the H9-H12 batteries in 2 columns
- Cables between the 2 columns
- Screws

• Control your consumables remotely via the ALMA SOLAR application
• Measurement of consumption and graphic reading on the application
• Monitoring 120A consumption per phase (three-phase)
• Scenario activation based on the states of connected devices, solar production, solar battery status, weather, time, location, brightness* (*depends on a device with sensor)
• Supplied with 3 current clamps

Buy your APS EZ1 micro inverter directly from our online store. The great special feature of this APS micro inverter is that it can connect 2 solar modules. They optimize the production of the two solar modules and yet make them completely independent of each other. Thanks to this new technology, you can reduce the number of micro-inverters and optimize profitability: more power and lower costs. With the EZ1 model, monitoring is already integrated and the inverter can be controlled via Wifi or Bluetooth.
A maximum of 2 units can be connected in series.

- Type CA15V small distribution board

- Powder-coated sheet steel, 800 x 300 x 160 mm

- 400V AC 50/60 Hz, 125 A

- IP44 protection, Protection Class II

Connects in parallel to your electrical circuit and connects directly to your Solax solar inverter to monitor your home consumption and regulate the power of your solar panels.

Measures between 5A and 200A per phase for 24mm diameter cables. 

This electric cable with a section of 4 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

Wifi communication card for connecting your ABB inverters UNO and TRIO via Wifi and monitoring their performance remotely.

- Product Type: FD17

- ComfortLine Series

- Dimensions: 1050 x 250 x 160mm

- Material: Plastic Cover

Buy your micro-inverter APS DS3 directly on our online webshop. The micro-inverter APS specification is allows a connexion for 2 solar panels on the same micro-inverter. It optimizes solar panels production and become them completely independent from each orders. With this new technology, you reduce the number of micro-inverter and moreover you optimize profitability: More performance and less expensive.

You must order the APS cable to connect the micro-inverters to each other.

Extend your FRONIUS inverter warranty Fronius Galvo 1.5-1, 2.0-1, 2.5-1, 3.0-1, 3.1-1; Fronius Primo 3.0-1; Fronius Symo 3.0-3-S, 3.0-3-M; Fronius Symo Hybrid 3.0-3-S to 10 years.

The Enphase Envoy communications gateway is the core of your network. Homeowners can easily monitor the status of their system using the LCD screen of the Envoy and get more detailed information for each module via Enlighten, the monitoring and analysis software by Enphase.

WIFI directly included in this ENVOY-S gateway.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

Frameless, transparent bifacial glass modules
Performance Guarantee
Positive Tolerance 0-5W
30-Year Warranty
Complete Protection

Currently available only in full pallets
(25 pieces)

- Model name: S753DR-E80
- Number of poles: 3
- Protection current: 80A 25kA
- Voltage rating: 400 V
- Device type: Selective main line circuit breaker

- U41 Small Distributor, flush-mounted

- Dimensions: 310mm W x 684mm H x 120mm D

- Protection Class II, IP31 Rated

- Indoor use, rated 125 A, 400V

The Modbus SolarEdge meter is used for photovoltaic supervision, consumption monitoring at home and for monitoring the power grid. The meter measures currents from 50 A to 1,000 A and supports residential and commercial installations. The meter connects to the SolarEdge inverter or gateway control and communication via RS485.

Card for Kostal product extension. Specific card for Germany.

- Wall-mounted enclosure

- Indoor use, IP54

- Rated current 250 A

- Dimensions: 1100 x 300 x 215mm

Wifi communication card to connect your SOLAX inverter and monitor its performance remotely.

This meter measures the power injected into the electrical network, the consumption of your home. To be used for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with 3 CT clamps 120A/40mA.

- Model name: S753DR-E100
- Number of poles: 3
- Protection current: 100A 25kA
- Voltage rating: 400 V
- Device type: Selective main line circuit breaker

With this Base Unit, the new SMA Home Storage can be set up directly on the floor as an alternative to the supplied wall bracket. One base is required for each battery tower.

This electric cable with a section of 6 mm2 for three-phase networks over a length of 30m. You must connect to the output of your inverter to your electrical panel. It can be installed in the air, underground, in water, in concrete, indoors, in cable ducts, etc.

VDE and IEC certified cable.

- Wall-mounted enclosure

- Indoor use, IP54 - 250 A, RAL 9016

- Dimensions: 1100 x 300 x 215mm

- Product: CA16V, partially constructed small distribution cabinet

- Technical specifications: 400V AC 50/60 Hz, rated current In of 125 A, protection class II, IP44 protection

- Dimensions: 950 x 300 x 160 mm

- Weight: 13,068 kg.

Set of 2 reusable handles for easy handling of the IQ-5P battery.

This single-phase Solax box allows the AC GRID output and the EPS output to be connected to the same injection point. This box works with Solax Hybrid SK-SU and Solax Hybrid X1-D-E inverters. The Solax Hybrid AC GRID output works with the power grid. The EPS output operates in the absence of electrical network, i.e. during a blackout. You have 2 inputs for 2 Solax outputs and 1 output for a parallel connection to your house grid.

Add this box if you wish to secure your power supply at all times and even in the event of a power outage.

Output raised to 97,1%
Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Output raised to 97,1%
Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Extend your ABB inverter warranty TRIO-5.8-TL to 10 years.

The WALLBOX power boost measures the power taken from the network, sends the data to the WALLBOX charger so that it regulates the charging power and avoids excessive energy consumption in the home, eliminating any risk of blackout.

- Product type: DF17U1B meter panel

- Dimensions: 1050 x 250 x 160 mm

- Power system: TN-S, 5-pole

- Rated current: In 40 A

- CA24V small distribution board

- 400V AC, 125A

- Dimensions: 650 x 550 x 160mm

If you have a FRONUIS GALVO SYMO or PRIMO Light version, you can add this card to establish a WIFI connexion.

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Output raised to 97,1%
Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

- Model: DF27U11B meter panel

- Dimensions: 1050 x 500 x 160 mm

- Protection Class: IP2XC

- Manufactured: Germany

Low price
WIFI connection (included)
Lightweight
Quick start
Single-phased inverter

Buy your communication GATEWAY TIGO ENERGY with CLOUD CONNECT an power supply box at the lowest price online only. This solution enables the communication between smart solar panels and panels with solar optimizers by TIGO TS4. The GATEWAY antenna is set up directly behind the smart solar panels, collects all the data and sends it over via RS485 cables to the CLOUD CONNECT. Thanks to this technology, all your solar panels are completely independent and you can optimize your solar installation’s power output.

Electrical box (continuous current) for photovoltaic protection. Cabinet includes wiring diagram. Required for each photovoltaic system. This DC box is needed for inverters with 2 independant entrances (2x MPPT).

DC box 2 x MPPT - DC breaker 25 A - 1000V, surge protector type 2, 1 string / MPPT - connexion with MC4.

The ECU communication gateway is the core of your network. Owners can easily monitor the status of their system using the LCD screen or get information by solar panel via the monitoring software and APS testing.

In addition to controlling the surplus management, you can remotely activate your hot water tank.

Connects directly via RS485 to the LG inverter. You will be able to monitor your home consumption and regulate the power of your solar panels. Measures up to 60A in three-phase.

- Item number: 446007

- Flush mounting, indoor use

- Multiple cable entry options

- Protection class IP31

- Wall-mounted, indoor enclosure

- Protection class II, IP54

- Rated current In 250 A

- Dimensions: 1100 x 800 x 215 mm

Measure the current of your home with this sensor that plugs around the corresponding power cable.

Electrical box (alternative current 3-phase) for photovoltaic protection. Cabinet includes the wiring diagram. Required for each photovoltaic system.

AC box 400 V AC 3-phase AC up to 10 kW with differential circuit breaker 16 A - 30 mA + surge arrester type A.

This meter measures the power injected into electrical grid, consumption of your home. The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 100V to 380V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

This meter measures the power injected into electrical grid, consumption of your home and power from another inverter SOLAX brand or other(dual version). The connexion type is available in the installation instructions at the bottom of this page. 

It measures a voltage from 40V to 400V. Use it for three-phase networks. Thanks to the CT clamps, there is no limit to the power measured.

Delivered with CT clamps.

Immediately cost-effective
Low price
Wifi monitoring

• Easy and Fast Assembly
• Reliability and Robustness
• High-Performance Monocrystalline Cell
• 30 Years Product Warranty
• Guaranteed Performance
• 100% Made in Europe

- Model: CA25V

- Dimensions: 800 x 550 x 160 mm

- Voltage: 400V AC

- Protection: IP44